Microsmith Computer Hardware EXPX6 User Manual

TM  
HOT LINK PRO!  
INC.  
WWW.HOT-LINK.COM  
Instructions  
Thank you for purchasing the HOT LINK PRO! Remote Control Booster System, a supersensitive, hidden, infrared (IR)  
remote control repeater. With HOT LINK PRO!, IR remote controls can operate equipment hidden in closed cabinets  
and increase the useful distance of remote controls up to sixty-five feet.  
Quick Setup Guide  
Caution: DO NOT enclose equipment not meant to be fully  
enclosed. While most equipment may not overheat in a  
moderately-sized cabinet, some equipment such as  
high-powered amplifiers and receivers may overheat and cause  
damage. Allow for ventilation through back of cabinet.  
Confirmation  
Emitter applied  
LED, Green  
over IR "EYE"  
1 Mount Receiver Eye in visible location using  
screw tab or VelcroTMtabs.  
on equipment  
2 Apply Emitters to original equipment eyes,  
Emitters  
removing red backing on adhesive tabs.  
to other  
equipment  
3 Mount confirmation LED using adhesive tab.  
TM  
4 Mount the Repeater Box with Velcro tabs.  
Repeater  
Box  
Mount  
Receiver Eye  
Plug in  
Power  
Supply  
5 Plug power supply into Hot Link Pro! and 120VAC  
standard outlet.  
Detailed Guide and Hot Tips  
Eye Window  
Receiver Eye  
Because the Receiver Eye is so sensitive, it can be located in a slot behind a cabinet door on the front or mounted on  
an exposed part of the cabinet top, an exposed shelf, behind a speaker grill, behind a cabinet "looking" out into the  
room or mounted in the toe-kick facing the floor. It can often work at the back of the room where equipment may be  
installed. Eye Window should not be facing direct sunlight, high powered flood lamps, 12 volt halogen lamps driven  
by switching type power supplies, or High-efficiency screw-in type fluorescent lamps. These items may emit too  
much Low Frequency (LF) RF, too much Pulsed IR or too much ambient light. If used in conjunction with other IR  
repeaters, verify they are not emitting spurious IR. Mount Eye at least one foot from your television, if possible.  
The Hot Link Pro is excellent at blocking LF RF from TV sets but can sometimes receive interference from larger sets.  
The Receiver eye may need to be shielded from direct view of Plasma Discharge TV screens that emit pulsed IR.  
Noise activity is indicated when the Green LED glows with no remote control activity. Find source of noise and  
eliminate or move Receiver Eye away from noise until LED is off. Addition of non-factory RCA extension cables may  
affect performance. Extension cables are available in custom lengths to 25 feet.  
Emitters  
Locate the IR eye of your equipment, using a flashlight to look through the  
faceplate (front) to find the eye, which may look like a small circle, see examples.  
Or check the equipment owners manual for the location of the remote control  
window. If the eye cannot be located with confidence, complete the step of  
connecting the Plug-in Power Supply. Then peel off red backing from clear tape  
on one Emitter and with the equipment turned on and it's face blocked from the  
hand-held remote control, do not block the HOT LINK PRO! Receiver Eye.  
Holding remote a few feet from Receiver Eye, press a known function button,  
moving the IR Emitter slowly across the front panel about a quarter of an inch in  
front of the surface, until the equipment responds to the remote control  
command. When best position is located, apply IR Emitter to front with sticky  
IR Window Examples  
side on equipment.  
Continued on next page...  
PDF created with pdfFactory trial version www.pdffactory.com  

Lenoxx Electronics Telephone PH 549 User Manual
LG Electronics Blu ray Player BD678N User Manual
LG Electronics Clothes Dryer DLEX3370R User Manual
Life Fitness Treadmill M051 00K58 A034 User Manual
Lincoln Electric Welder 11124 User Manual
Lincoln Electric Welder IM10019 User Manual
Makita Grinder 9564 User Manual
Manitowoc Ice Ice Maker K00066 User Manual
Martin Audio Portable Speaker WTUB User Manual
Melissa Vacuum Cleaner 640 152 User Manual